Heat Siphon Pool Heaters
Warm Water at the Lowest Cost Possible: 85°F – 24/7 for $2.50/Day*
*One C375HP Heat Siphon will maintain a 15 x 30 pool at 85°F – 24 hours per day per week for $2.50 per Day in Portland, Maine or Miami, Florida
Heat Siphon technology has always been the lowest cost method of heating swimming pools in the United States and eventually it will be virtually the only method used. Why? Heat Siphon produces heat at:
- 1/2 the cost of Natural Gas
- 1/5 the cost of Electric Resistance
- 1/6 the cost of Oil or Propane
Cheap Oil and Natural Gas are scarce. Industry, Government and University studies have all projected steady price increases while the fuels used to generate 2/3 of the Nation’s electricity (coal, nuclear & hydroelectric) are either ABUNDANT OR INEXHAUSTIBLE.
HOW HEAT SIPHON® WORKS:
SAFE DEPENDABLE HEAT PUMP TECHNOLOGY – NOT MAGIC
Heat Siphon is a heat pump designed specifically for recreational water heating. Water coolers, refrigerators, dehumidifiers, freezers and air conditioners are ALL HEAT PUMPS. All these appliances use the same dependable refrigeration technology to move heat from one place to another by evaporating and condensing refrigerant in a sealed tubing system.
Heat Siphon will always be 1/4 to 1/6 the cost of straight electric resistance heat.
Why? For every unit of electricity Heat Siphon uses, it produces 4 to 6 units of heat. Sound like magic? Hardly. With the same technology a central air conditioner removes 2.5 to 3 units of heat from your house for every unit of electricity it consumes. For a detailed explanation of how a swimming pool heat pump works INCLUDING an ANIMATION, visit www.HEATSIPHON.com and click on the “HOW IT WORKS tab!!
HEAT PUMPS ARE SAFE TECHNOLOGY – Heat Siphon has been tested by an independent laboratory and approved as meeting nationally recognized UL and CSA safety standards. EVERY HEAT SIPHON® IS TESTED BEFORE, DURING AND AFTER FINAL ASSEMBLY FOR HEAT OUTPUT, WATER AND REFRIGERANT SEALS AS WELL AS SAFETY COMPLIANCE.
ONE KNOB or TWO BUTTONS . . . Just SET IT & FORGET IT.
ANALOG MODELS – just turn the dial all the way up and let your Heat Siphon run until
your pool is warm, then turn the knob slowly counterclockwise until your Heat Siphon shuts off.
DIGITAL MODELS – just press the “UP” or “DOWN” key to set the water temperature, then 3 seconds after the last key press . . . a “beep” . . . confirms your setting.
DONE – You’re Set – TIME TO FORGET IT AND JUMP IN YOUR NICE WARM POOL!!!
HEAT SIPHON® . . . AUTOMATICALLY ON-THE-JOB
Heat Siphon will automatically maintain the pool temperature within 1.5 °F. The thermostat and water flow switch constantly monitor pool temperature and pump operation and they turn on your Heat Siphon only when needed and only while your circulating pump is running.
Heat Siphon uses a thermostatic expansion valve to operate the heat pump system at maximum efficiency regardless of air or water temperatures. It shuts down if your pool filter clogs or fresh air supply to the unit stops, or if in danger of icing (air temperatures below 42°F). When the icing threat is gone, your Heat Siphon automatically resumes heating your pool.
Since gas heaters are so expensive to run, all gas heater manufacturers try to keep the cost of the heater as low as possible. Most gas pool heaters have a sheet metal cabinet and a copper heat exchanger with cast iron water connections. Usually they are assembled with galvanized steel screws. INEVITABLE RESULTS – rust and corrosion.
Heat Siphon®’s electrically isolated Pure Titanium Heat Exchanger, PVC cabinet and stainless steel hardware, make it CORROSION PROOF. Its sealed refrigeration system, weatherproof PVC control box and totally enclosed fan motor are all designed for years of trouble free service.
Two more shortcomings of gas heaters are heat exchanger scaling & soot deposits, which drastically cut down heat transfer efficiency. The pool water flows through small flow channels and the hot combustion gas heats the outer tube surface. If the flow is too low, water boils inside the tubes leaving scaling deposits which block and overheat it. Too high water flow causes condensation & rusting or soot deposits.
Heat Siphon®uses no flame so heat transfer occurs about 2000°F lower than combustion gas. The pool water flows on the OUTSIDE of the Titanium tubes ELIMINATING heat exchanger scaling and blockage.
With Heat Siphon® there’s no pilot light to blow out, no flue gases, no dangerous hot surfaces, no scaling, no gas piping to run, no unsightly gas tanks and no high fuel cost.
ONE HEAT SIPHON® CAN EASILY LAST LONGER THAN THREE GAS POOL HEATERS!!
HEAT SIPHON® MADE in the USA
Sold WORLD-WIDE Since 1983
HEAT SIPHON® FEATURES
SERVICING ALL MAJOR BRANDS
We are Proud to Service these Major Brand Products Goodman, Rheem, RUUD, Trane, Lennox, American Standard
stephen k. denny inc. Air Conditioning & Pool Heating, Stuart, Jupiter, Delray, Florida 24-hour 7-day emergency services, 100% SATISFACTION GUARANTEE, We provide Free estimates and 18 months special financing
Proudly Servicing Air Conditioning for Port St. Lucie, Ft. Pierce, Jensen Beach, Stuart, Palm City, Hobe Sound, Port Salerno, Indiantown, Tequesta, Jupiter, Juno Beach, Palm Beach Gardens, North Palm Beach, Lake Park, Riveria Beach, Loxahatchee, the Acreage, West Palm Beach, Belle Glade, Manalapan, Mangonia Park, Royal Palm Beach, Wellington, Palm Beach Shores, Palm Springs, Lake Worth, Greenacres, Lantana, Boynton Beach, Delray Beach, and Boca Raton offering fast 24/7 emergency service.